PCV Valve and Intake Manifold Motor Warranty Extension

06F129101P Front Detail

I recently received a letter from Volkswagen of America stating that the warranty for the pcv valve and intake manifold motor has been extended to 10 years/120,000 miles. You will also be eligible for reimbursement if you paid for repairs on any of these parts. Signs of pcv failure may include loss of boost pressure, poor idling and sometimes oil being pushed out of the oil cap. Intake manifold failure usually results in poor cold starting and sluggish low end performance. Either case can also cause the check engine light to come on.

PCV Valve

Here a Golfmkv.com link to common 2.0T FSI issues.

I’ll upload the document as soon as I can scan it in. Here we go.

20120113-090344.jpg

20120113-090355.jpg

Advertisements

“G” Revision PCV Valve Internals

I opened up my non-functional revision G pcv valve and took a few pictures, enjoy.

Revision G Check Valve - This one is broken

Revision G Diaphragm and Spring

Revision G PCV Internals

Revised OEM PCV and Crankcase Breather Tube

06F129101P Front Detail

In my current quest to return some parts back to OEM spec, I’ve recently purchased the latest revision PCV components.  The latest revision PCV valve is “P” with the part number 06F129101P.  There is also another revision of the rear breather tube, part number 06F103215B.  The valves in the latest revisions seem much stronger compared to my old “G” revision.  The check valves are now spring loaded instead of free moving.  I don’t know when they switched to the spring loaded valves because I completely skipped over the 2 or 3 other revisions.

06F129101P Valve Detail

If you’re wondering why I went back to stock, I wanted to remove the catchcan I’ve been running.  An intake manifold teardown by a forum member  revealed that catch cans do little to aid in preventing the intake valve deposits inherent to direct injection engines.  I have also been thinking about the lack of intake vacuum working on the crankcase.  In the catch can setups, vacuum is sourced from intake air moving over the rear breather tube exit.  I think it is a max of 3″ of mercury according to BSH and this occurs in the higher rpms under boost.  At lower rpms, actual vacuum may be much lower.  Too little flow or stagnant flow through the valve cover may allow the blow-by gasses to start forming deposits.  I’ve noticed a little grime building up around the oil cap area, despite the regular oil changes.  The accumulation of these blow by gasses can contaminate oil and deteriorate it much faster as well.  Another side effect of routing all gasses through the rear breather tube seems to be, ironically, more oil in the charge pipes.  If a recirculation type catch can does not catch all the vapors, the rest end up condensing in charge pipes and intercooler.  The stock system sends them directly to the intake manifold to be burned off.  The way the stock system works, it only reroutes vapors through the charge piping and intercooler under boost.  When I installed my throttle pipe, a good amount of oil came pouring out of the pipes.

06F103215B Check Valve Detail

Now oil vapor in the in the intake charge is detrimental to performance.  This is where a catch can does help.  Oil vapor can effectively reduce the octane level of the intake charge and lead to more knock, which would then decrease performance.  I haven’t noticed a performance difference since I switched back to the stock system but then again, my car isn’t exactly a horsepower monster.  It is a compromise situation but after many miles of thought, I’d rather have the stock system deal with the evacuation of the crankcase gasses.  The stock pcv system flows a lot and I don’t think some of the catch cans flow enough.

06F129101P Rear Detail

The stock pcv valves have not been models of reliability, which is one of the reasons catch catch cans have sold so well. Modified and stock cars alike can blow through them.  These newer parts are now several revisions deep and they seem to be much more robust pieces.  The rear check valve in the breather tube looks much better.  The front pcv check valves have a more positive engagement compared to the “G” revision I compared it to.  I guess only time will tell!

06F103215B

Revised OEM PCV and Breather Tube Part Numbers

06F129101P Front PCV Valve Detail

The 2.0T FSI’s pcv system has gone through several revision changes.  Earlier valves failed rather easily, causing boost pressure to creep into the crankcase.  Checkvalves would leak and pressure diaphragms would rip.  Symptoms include oil coming out of the valve cover gaskets or oil cap, reduced gas mileage and power or increased oil consumption.  An unsteady idle is another symptom and severe cases will cause a code to be set.  This latest one seems to be a bit more robust than previous versions.  The check valves are spring loaded now instead of free floating for more positive engagement.  If you want to stay stock here are the latest part numbers.

The latest pcv system part numbers are 06F129101P for the front pcv valve and 06F103215B for the rear breather tube with check valve.  The 06F129101P part number only works on rear breather tubes that have a built in check valve.  Certain VIN’s / model years have breather tubes that do not have rear check valves.  The only way to be sure it to pull it off and check for the valve.  Here’s some excellent information for replacing the PCV valve and breather tube.  The link also shows the Eurojet check valve solution so just ignore it if you are not going that route.

06F103215B Rear Breather Tube with Check Valve